The 3500/33 16-Channel Relay Module is a full-height module that provides 16 relay outputs. You can place any number of 16-channel relay modules in any of the slots to the right of the Transient Data Interface (TDI) Module. Each output of the 3500/33 16-Channel Relay Module can be independently programmed to perform voting logic. The GE / Bently Nevada 3500/33 Series 16-Channel Relay Module is a full-height module that provides 16 relay outputs. Any number of 16-Channel Relay Modules can be placed in any of the slots to the right of the Rack Interface Module.
Each output of the 16-Channel Relay Module can be independently programmed to perform needed voting logic. Each relay utilized on the 16-Channel Relay Module includes “Alarm Drive Logic”. Each relay utilized on the 16-Channel Relay Module includes “Alarm Drive Logic.” Programming for the Alarm Drive Logic uses AND and OR logic, and can use alarming inputs (Alert and Danger statuses), Not-OK, or individual PPLs from any monitor channel or any combination of monitor channels in the rack. Users program this Alarm Drive using the 3500 Rack Configuration Software to meet the specific needs of the application. Each relay of the module includes Alarm Drive Logic. Programming for the Alarm Drive Logic uses AND and OR logic and may use the following:
Alarming inputs.
Not-OK.
Individual Measured Variables from any monitor channel or any combination of monitor channels in the rack.
FEATURES:
Front panel LEDs
Alarm drive logic
5.8 watts typical power consumption
Epoxy-sealed
Single-pole double-throw (SPDT)
250 Vrms installed as standard
100,000 cycles relay contact life
COMPATIBILITY:
The 3500 Rack Config, version 3.3 or later, is required for the 16-Channel Relay Module.
The Data Acquisition Software, version 2.40 or later, is required for the 16-Channel Relay Module.
The 3500 Data Display Software, version 1.40 or later, is required for the 16-Channel Relay Module.
If the 16-Channel Relay Module is part of the functional safety (SIL) system, the restricted voltage is required by the functional safety certificate. For functional safety (SIL) systems, higher voltages are not permitted.
The Single Channel Relay Module is a convenient board that can be used to control high voltage, and a high current load such as motor, solenoid valves, lamps, and AC load. It is designed to interface with microcontrollers such as Arduino, PIC and etc. The relay terminal (COM, NO, and NC) is being brought out with a screw terminal. It also comes with a LED to indicate the status of the relay.
SPECIFICATION:
Digital output controllable
Compatible with any 5V microcontroller such as Arduino.
Rated through-current: 10A (NO) 5A (NC)
Control signal: TTL level
Max. switching voltage 250VAC/30VDC
Max. switching current 10A
Size: 43mm x 17mm x 17mm
PRODUCT DESCRIPTION:
8 SPDT, 5Vdc relays activated by infrared remote control
On/off activation latching one or more, or all at the same time
10 Amp relay will switch AC or DC devices
Individually optoisolated relays
Terminal strip for control by Arduino or another microprocessor
Receiver / relay board, 136 x 52 x 27mm
Screw-clamp terminals for input and output
Multi-button IR remote control, 86 x 40 x 7mm
IR remote battery, CR2025 button cell included
25′ range, line-of-sight
Relay modules use low-level data signals to switch relays capable of handling loads up to 10 Amps. Ideal for devices like PIR detectors and other sensors that output low-level signals that need to turn another device on or off. Great for use with Arduino and other microcontrollers. Onboard LED indicators light when a relay is switched. Convenient screw terminals for relay outputs. 0.1″ header for voltage and signal input. Available in 1, 2, and 4 relay configurations.
WOC is a global aftermarket supplier of high-quality OEM and non-OEM replacement spare parts and services for the General Electric and Bently Nevada heavy-duty, industrial gas turbines. Through our worldwide network, we are able to offer clients a wide range of products for the GE™ designed MS3002, MS5002, MS5001, MS6001, MS7001, and MS9001 gas turbines. Our goal at Gas Turbine Parts & Services, Inc. is to offer owners and operators of these gas turbines an experienced, reliable, and competitive source for all of their gas turbine needs.
Our Mission is to provide you with the parts, repairs, and services you need when you need them. WOC is a full-service provider of heavy-duty & aero-derivative industrial gas turbine maintenance, including spare parts distribution, component repairs, and field services.
WOC holds a large inventory of New, Used, and Refurbished Capital Spares that are available for immediate shipment. More details and inspections of these parts can be provided and arranged upon request.
We think knowledge is priceless. We can help you resolve or avoid issues that pose a threat to your company because we have top engineers with over 20 years of expertise on our team.
FREQUENTLY ASKED QUESTIONS:What is Bently Nevada 3500/33?
It is a 16-Channel Relay Module developed by Bently Nevada.
Which Data Acquisition Software is required to configure the module?
Version 2.40 or later, is required for this 16-Channel Relay Module.
What is the average input power consumption of the relay module?
5.8 watts is the average input power consumption.
How to Check Price and Availability For 3500/33?
Please Contact World of Controls FZE for sales at +1 609 385 1231 or Request a Quote.
Read more: Smart Parcel Lockers for Business
